The router does not dynamically update port forwarding settings and cannot port forward to your Iomega StorCenter ix if its IP address changes. To resolve this problem you can try one of the following techniques: Increase the length of the DHCP lease: Your router will attempt to remember all DHCP clients and give them the same IP address every time they request an IP address; however, the router will forget clients if they do not request an IP address for a certain amount of time.
If your network requires DHCP, this may be a good solution; however, it is not always guaranteed to work. You may need to occasionally update your router's port forwarding settings. This ensures that the Iomega StorCenter ix will always get the same IP address and your port forwarding settings will always be correct. See the manual that came with your router for more information on configuring DHCP settings. Log in to your router and write down the DHCP range it is using.
For more information, check the Network Settings section of this manual. For example, if your router is distributing IP addresses in the range of Make sure you are assigning the Iomega StorCenter ix an IP address that is not in use by another device.
Enter a subnet mask. The subnet mask describes the size of your network. For most networks this will be Enter a gateway address. In most cases, this will be the IP address of your router. This non-transferable, limited warranty is only to you, the first end-user purchaser. The warranty begins on the date of purchase and lasts for a period of one 1 year for products purchased in the Americas, the Asia-Pacific region, or non-European Union nations in Europe, the Middle East, or Africa; ninety 90 days for Iomega reconditioned products purchased in these regions; or, two 2 years for products purchased by an end-user in member nations of the European Union.
Customers who register their new products at www. Reconditioned products are not eligible for a warranty extension. Excluded Products and Problems This warranty does not apply to: a Iomega software products; b expendable components such as fuses or bulbs; or c third-party products, hardware or software, supplied with the warranted product.
Remedies Your sole and exclusive remedy for a covered defect is repair or replacement of the defective product, at Iomega's sole option and expense shipping may be charged , and Iomega may use new or refurbished parts or products to do so. If Iomega is unable to repair or replace a defective product, your alternate exclusive remedy shall be a refund of the original purchase price.
The above is Iomega's entire obligation to you under this warranty. In no event shall Iomega's liability exceed the original purchase price of the drive or the media disk. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Obtaining Warranty Service You must notify Iomega within the warranty period to receive warranty service.
Just as technology and market conditions vary, Iomega's specific customer support policies including fees for services and procedures change over time. To obtain information about Iomega's current policies or warranty service, please visit our website at www. Contact information for Iomega Customer Service can be obtained on our support website at: Americas www.
Iomega will not protect, recover, or return data during warranty service so you should duplicate your data before shipment. Any implied warranty required by applicable law shall be limited in duration to the express warranty term.
Some jurisdictions do not allow disclaimers of implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from jurisdiction to jurisdiction. Any suit for breach of any warranty on your product must be filed within one 1 year of the first date the suit could have been brought.
Before you can use your Iomega StorCenter ix, you must connect all the cables and turn it on. Once you have connected the hardware, you can install the optional Iomega Storage Manager Software and begin using your Iomega StorCenter ix2- Iomega Storage Manager optionally installed on your local computer, it discovers any Iomega storage devices on your subnet, maps device Shares to computers, and provides local access to your content.
It provides access to Shares through your computer's file management program, such as Windows Explorer or Mac Finder, allowing you to drag and drop many files between your computer and the Iomega StorCenter ix Installing the Iomega Storage Manager is optional.
Home Page serves as a web-accessible interface to your Iomega StorCenter ix If you are using Remote Access, the Home page is the landing page to access your device. You can access the Home page of your Iomega StorCenter ix by entering the device name or IP address directly in your browser. If security is enabled and you are an administrator user, you can access the Iomega StorCenter ix Console from the Home page by clicking.
How do I It also displays the overall state of your Iomega StorCenter ix There are a number of ways to access the features of the Iomega StorCenter ix Console.
You can select one of the predefined categories, use the All Features page that lists every feature alphabetically, or search for a feature by keyword. When security is enabled, only an administrator user can access the Iomega StorCenter ix Console. On this page, you can configure some basic device features by clicking the appropriate link.
The current setting of the feature displays above the link. You can also configure all features shown on the Setup page by accessing the specific features directly. The Properties column displays the features that are enabled for each Share. Share Information The Information section displays the Share name, graphically displays the space usage of the Share, and allows you to view the content using the web-based content viewer. To learn how to modify your Share information, refer to Managing Shares.
Access Permissions Access Permissions section contains a list of users who currently have access to that Share. Access Permissions displays when the Iomega StorCenter ix is secured, otherwise the section is not included in the Share.
By default, user Everyone has read and write access to that Share, which means that all users have open access to that share. The Content Viewer is divided into two panes. The left pane lists the Shares on the Iomega StorCenter ix and allows you to delete or add a Share. If you select a Share that contains pictures, you can start a slideshow of the pictures in that Share. The right pane lists the files and folders in a Share and allows you to delete content or upload a file to the Share.
To delete multiple files simultaneously, hold the Ctrl key on your keyboard and select each file, or drag your mouse over the filenames. Share content can be sorted, and you can switch between a list view and a thumbnail view of the files. When you are looking at content in a list view and you hover your mouse over an image, a thumbnail view of the image displays next to your mouse. If all the content cannot fit on one page, there are pagination controls that allow you to continue browsing the content.
To add a new Share, click Add a Share. Type a name for the Share. All Shares must have a name. Names cannot exceed 32 characters.
The following are not valid Share names: global, homes, printers 3. Click Create. To modify an existing Share, click to expand the Share. Changing Share Information 1. Modify the existing name for the Share. Choose whether to enable content search and media sharing. When Media sharing is enabled, the media server scans this Share for any media content and makes it available to anyone with access to your network, even if this Share is secured.
If you do not want media content made available to anyone, do not check this option. When Media sharing search is enabled, displays in the Properties for that Share.
Click Apply to save your changes. Changing Access Permissions You should enable security on your Iomega StorCenter ix before changing access permissions. Expand Access Permissions to change user permissions to this Share.
A security icon displays in Properties indicating a secure Share. When a secure Share is first created, Everyone has read and write access to that Share by default, which means that everyone on your network can read, write, and delete files to and from that Share. When user Everyone has Read and Write permissions to a Share, the Share is not secure and is open to all users. Check Allow users to change file level security to allow file and folder permissions to be set through other programs, such as Windows Explorer, independent of the Iomega StorCenter ix Setting this option allows users to put additional access restrictions on individual files and folders.
To limit access to this Share to a specific set of users, click the and choose one or more users from the pop-up window. If you have created groups, you can also limit access for them in this way. In the Access Permissions section, check Read, Write, or both to set access to this Share for each user. To remove a user, leave both Read and Write unchecked for that user.
If you grant Read and Write permissions to Everyone, the list of users is also cleared since all users Everyone has access to this Share. To enable NFS, first click the switch on from the Protocols page. You cannot apply a rule to a public Share. Rules are added to specify the hosts that are allowed to access Shares using NFS. Use this table to add NFS rules to specify access for hosts. When the rule is added, read access is automatically set to the Share. Select Write to allow users to write to that Share.
Use and to modify the rule priority for NFS access. Making a Share an Active Folder 1. You can optionally enable Active Folders on a Share to allow you to associate this Share with a specific feature that will happen automatically when files are copied to the Share.
You can only set one Active Folder option per Share. Expand the Active Folder section and check Enable. To delete an existing Share, click to expand the Share. In the Information section, click Delete to delete the Share. In the Delete Share confirmation pop-up window, click Yes. If you do not wish to delete the Share, click Cancel to return to the Shares page. The following list identifies the Shares page icons: identifies a Share with Media Sharing enabled.
Use Email Distribution to share files with an email list. To prevent email distribution list spamming, the Iomega StorCenter ix allows lists of or fewer email recipients and sends a maximum of six emails in a hour period. Configuring an Email Distribution Active Folder 1. Check Enable. Select Email Distribution from the drop-down menu. Include an email address in the Sender Email Address text box. Distribution is sent from this email address. You can add multiple email addresses in the Email To: text box by separating them with commas, spaces, or semicolons.
Add a subject and email message for your recipients. Check Send the file as an attachment, Send a link to the file, or both. Once configured, all files in this Share are sent by email to your recipients. Click View Transfer History to see the transfer activity from this Share to your account. Manage a Share 25 Iomega StorCenter ix Facebook Active Folders You can optionally enable Active Folders on a Share, which enables you to associate this Share with a specific feature or operation that occurs automatically when files are copied to the Share.
You can configure a Share as a Facebook Active Folder so that photos added to that Share are automatically uploaded to your Facebook account.
If you do not have a Facebook account, go to the Facebook website to open an account. Configuring a Facebook Active Folder 1. Select Facebook from the drop-down menu. Click Configure Facebook account access to configure your Facebook account. You will be taken to a Facebook page to configure your account. Follow the instructions provided by Facebook. Check Delete files after upload to delete images from the Share once they are transferred to your Facebook account.
Images can also be resized prior to upload. Check x, x, or enter a custom resolution for resizing images. Once configured, all of your images in this Active Folder will upload to your Facebook account.
You can configure a Share as a Flickr Active Folder so that images and albums added to that Share are automatically uploaded to your Flickr account. If you do not have a Flickr account, go to the Flickr website to open an account. Configuring a Flickr Active Folder 1. Select Flickr from the drop-down menu. Click Configure Flickr account access to configure your Flickr account. You will be taken to a Flickr page to configure your account.
Follow the instructions provided by Flickr. Check Delete files after upload to delete images from the Share once they are transferred to your Flickr account.
Once configured, all of your images in this Active Folder will upload to your Flickr account. Your original photos added to this Share can also be kept while a copy of the new resized version is created.
The resized photos are saved to a folder on the Share named by the photo size you choose, such as x Configuring a Photo Resize Active Folder 1. Select Photo Resize from the drop-down menu.
You can set a size for your pictures. Select x, x, x, or enter a Custom Resolution for resizing images. You can keep a copy of the original by selecting Keep the original files after resizing. To add a watermark to your photo, select Add a watermark to the photos. Click the Watermark file icon to apply a watermark image to your file. Once configured, all of your photos in this Active Folder will be resized to your settings. Click View Content to see the files in this Share.
How to Set Up a Torrent Active Folder Torrent downloads allow you to share files using a peer-to-peer file sharing protocol. With Torrent Download, you can download files using the torrent protocol to your device and then those files can be uploaded by other torrent users.
Configuring a Torrent Active Folder 1. Select Torrent from the drop-down menu. Click General torrent settings to set up Torrent settings. Refer to Torrent Downloads for more information on configuring your Torrent downloads. If you do not have a YouTube account, go to the YouTube website to open an account. Configuring a YouTube Active Folder 1. Select YouTube from the drop-down menu.
Check Delete files after upload to delete videos from the Share once they are transferred to your YouTube account. Once configured, all of your videos in this Active Folder will upload to your YouTube account. Setting Write Caching Select a value for disk write caching. Write caching is a mechanism that attempts to separate the fast processing speed of the Iomega StorCenter ix from the relatively slow mechanics of actually writing data to drive.
With write caching disabled, every write to drive will cause the Iomega StorCenter ix to wait while the data is written to drive, which can slow performance. When write caching is enabled and the Iomega StorCenter ix sends a write request to the drive, instead of writing directly to the drive, it writes the data to cache which is much faster and sends an immediate acknowledgement to the Iomega StorCenter ix saying the write is complete.
The system can then proceed without having to wait for the data to actually get written to drive, which will occur in the background. While write caching does improve performance, there are some risks. Because the system will respond that the data has been written to drive when in fact it has only been written to cache, should the Iomega StorCenter ix lose power any data that did not get completely written to drive will be lost forever.
This is because cache memory is volatile. If you lose power, the contents of the cache are lost. Therefore, if there were any pending writes in the cache that were not written to the drive yet, they will be lost forever. Using a UPS Uninterrupted Power Supply can mitigate the risk associated with write caching, which is why it is recommended to only enable this feature when a UPS is connected.
Applying Global Drive Management Settings 1. Click Settings. You see this option only if there is at least one unused drive on the Iomega StorCenter ix To change the protection, choose a value from the drop-down menu: Mirror RAID 10 Uses half of the storage space for protection, leaving half for actual data.
None Turns off data protection and leaves your data vulnerable to data loss. Select a value for disk write caching. So, if you lose power, the contents of the cache is lost. Check Enable periodic consistency check to enable a monthly parity or mirror consistency check. The check helps to prevent a single drive failure from becoming a two-drive failure, resulting in data loss. The check runs for several hours and can affect performance of the Iomega StorCenter ix2- If you do not want to run the check, uncheck this option.
Drive status An image on the Drive Management page provides information on the drive status of your Iomega StorCenter ix The image displays the physical layout of drives and the drive slot numbers. If a drive has a circled letter, it is a member of a Storage Pool. When you connect external storage to your Iomega StorCenter ix, that device content is accessible from the Shares page. Safely removing external storage Click to safely remove the external storage.
A confirmation dialog will display. Click Yes to remove the external storage. When the external storage has been removed from the External Storage table, it is safe to remove and you may unplug it from the Iomega StorCenter ix When the external storage is safely removed, its associated Share is removed as well.
With Mutual CHAP checked, the client performs an additional check to confirm that it is using the correct device. Enter a device secret password for Device Secret and then enter it again in the confirm box. If you are using another type of software or hardware initiator, you must use the native tools provided with your initiator to connect your iSCSI drives. Expand the Connected Clients section. If the iSCSI drive is in use, you will see a list of connected client computers running initiator software.
Enter a name for the iSCSI drive. This field displays when your Iomega StorCenter ix is new, has no existing volumes, and supports multiple volumes. This field displays when your Iomega StorCenter ix is new or being upgraded and has only one volume. If the Create a volume and Use an existing volume options display, select: Create a volume to create a new volume for your iSCSI drive. This option displays when your Iomega StorCenter ix is new, or if you are upgrading your Iomega StorCenter ix and it has available space in its Storage Pools.
Use an existing volume to use an existing empty or shared volume. This option displays when you are upgrading your Iomega StorCenter ix, have available space in your Storage Pools, and have already created multiple volumes. To use an existing shared volume, select Shared Volume, select the existing volume, and enter a name for the iSCSI drive.
Enter a size for the iSCSI drive. Changing Access Permissions 1. To limit access to this iSCSI drive to a specific set of users, click the and choose one or more users from the pop-up window. When you have created groups, you can also set access for them in this way. If you grant read and write permissions to Everyone, the list of users is also cleared because all users Everyone have access to this iSCSI drive.
AFP is on by default. To enable AFP, click the switch on. Configuring Bluetooth settings 1. To enable Bluetooth, click the switch on. Once Bluetooth Transfer is enabled, check the Enable security checkbox to require Bluetooth users to supply a unique PIN that they have defined before allowing them to transfer files to the destination Share on the Iomega StorCenter ix If you have enabled security, you must define a unique PIN number, which will be supplied by devices attempting to upload data using Bluetooth.
To set the destination Share, click. Click Apply to save your settings. To change any Bluetooth settings, click. All files are owned by user guest, and all users accessing the Iomega StorCenter ix have the same access rights.
If you have enabled Active Directory on your Iomega StorCenter ix, only this option is available for mapping client computers.
To have all users map as themselves, including root, select Allow all client users full access. NFS provides another protocol for sharing storage data with Linux hosts. When NFS is enabled, you can configure rules for host-based access to secure Shares. Rules can be added to secure Shares to specify the hosts that are allowed to access Shares using NFS.
To change any NFS settings, click. For more information on Copy Jobs, refer to Copy Jobs. If you enable the Iomega StorCenter ix as an rsync server, you can optionally set up a user account on the Iomega StorCenter ix for secure rsync Copy Jobs. Configuring rsync server settings 1. To enable rsync server, click the switch on. Once turned on, supply a port that the rsync Server uses.
To create a secure user account, check Configure secure rsync credentials. The username is preset as rsync. Enter a password and confirm it for the rsync username. When you create a secure rsync user account on the Iomega StorCenter ix, you allow other devices to securely copy to or from it. To change any rsync server settings, click.
SNMP should be disabled unless you are specifically providing information to a management system that requires this information. Configuring SNMP settings 1. To enable SNMP, click the switch on. Enter a unique username and password to define the community. Confirm your password. Enter the IP address of the host in the Trap Receivers text box. To grant access to multiple receivers, list all of them in the text box, separating each entry with a space. To change any SNMP settings, click.
Namespace A virtual Share containing other folders that are located on different devices throughout a network. DFS root An object that consolidates all the folders in your network and makes them available through a single entry point.
Configuring Windows DFS settings 1. To enable Windows DFS, click the switch on. Enter a DFS root name. Click Add a link to begin adding DFS links. Enter the DFS link name, which includes the name of the host and folder to which you are linking.
HTTP offers faster performance but is not secured. Refer to your operating system's documentation to learn how to access files through WebDAV. Configuring WebDAV settings 1. To enable WebDAV, click the switch on. Refer to your router's documentation to learn how to set these values. To enable Windows File Sharing, click the switch on. Setting QuikTransfer 1. Select a destination folder for the default QuikTransfer Copy Job by clicking and selecting a folder in the file browser. The file browser provides a way to select a Share and all its folders, or just some of the folders under a Share.
Click Apply to save your setting. With Torrent Download enabled, you can download files using the torrent protocol to your Iomega StorCenter ix and then those files can be uploaded by other torrent users. After you have added torrent jobs to your Torrent share, the Torrent Download page displays a table of torrent jobs, both downloads and files available for upload.
Multiple torrent files can download simultaneously. The table information includes the name of the data file, its size, download or upload status, and amount of time left before the torrent job completes. For more information on adding a torrent, refer to Adding a torrent.
Enabling Torrent Downloads 1. Click the switch on. Click Settings to modify the torrent download and upload settings. In the pop-up window, type a value for Maximum Download Speed. Maximum download speed sets the rate at which files are downloaded to your device. Type a value for Maximum Upload Speed.
This is the maximum upload speed for files being uploaded by other users from your device. The upload speed can affect device performance, as it sets the speed at which other users upload a file unprompted from your device.
It is recommended that you choose a value that does not strain the performance of your device and impact other work on it. Set a Port value used by torrent peers to upload files from your Iomega StorCenter ix The port value should be a number between and , and your router must be configured to allow port forwarding on the same port. Refer to Configuring your router for torrent downloads for more information on how to do this. Managing torrent downloads In the Torrent Download table, you can perform the following actions: Pause or resume a torrent job.
Click to pause a torrent download. When a torrent download is paused, you can resume the download by clicking. Delete a torrent job. Click to delete the torrent download. Open the Shares page. Expand the Share that is enabled as a Torrent Active Folder. Any Share can be enabled as a Torrent Active Folder. Copy the downloaded torrent file to the Torrent Active Folder Share. The torrent file immediately starts to download to the Share. An administrator user can monitor its download progress on the Torrent Download page.
All users can monitor the download progress through the content viewer on the Torrent Share. On the Torrent Download page, select a torrent you want to delete. Click the under the Action column to delete the torrent. Click Yes to delete the torrent. Most routers refer to this as port forwarding or application access and it is recommended that you refer to your router's documentation to learn how to set these values. Port information used to configure your router The following information may be required to manually configure your router: Forward the port to your Iomega StorCenter ix IP address identified in the table: Device IP Address An example of a Copy Job scenario is if you keep pictures from your digital camera on a separate USB drive, but you also want to maintain a backup of these pictures on your Iomega StorCenter ix Using Copy Jobs, you can create a task that copies your photos on the USB drive to a Share on your Iomega StorCenter ix, and you can set that task to a schedule so the images automatically copy at a specific time.
This ensures that your photos are always safely backed up to your Iomega StorCenter ix in the event your USB device ever fails or is lost. All saved Copy Jobs display on the Copy Jobs page. From there, you can manually start and stop a Copy Job, view Copy Job information, modify a Copy Job, check its last run status, and, if applicable, view when the Copy Job is next scheduled to run.
When defining a Copy Job, you can copy data from or to any of the following: Any NAS device automatically discovered on the same subnet as your Iomega StorCenter ix Any NAS device that you manually add to the subnet using the Iomega Storage Manager Any external storage device, such as a USB device, connected to your Iomega StorCenter ix When selecting what data to copy on the source storage device, you can choose a specific folder or all folders.
You can also copy from a folder on an external storage device mounted to your Iomega StorCenter ix When selecting the destination device, you can copy files to the top-level folder on the destination device the default option , or to an existing folder on this device, which adds the copied files into folders.
You can manually start or stop a Copy Job by clicking start or stop buttons on the Copy Job page. You can schedule a Copy Job to run automatically at a set day and time. This is known as the QuikTransfer option. The information section includes the name of the Copy Job, date and time it last ran, and its next scheduled time. Click to stop a Copy Job. Click to delete a Copy Job. Click the Schedule section to view the Copy Jobs schedule.
On the Copy Jobs page, click. A Copy Job is added to the top of the list and the Information section displays. Enter a name for the Copy Job. The Overwrite Setting determines what happens to files in the destination location if they have the same name as those in the source location.
Select one of the following values from the Overwrite Setting drop-down menu: Overwrite and don't delete — Files in the destination location are overwritten with files from the source location. Any files in the destination location that are not in the source location are preserved.
Overwrite and delete — Files in the destination location are overwritten with files from the source location. Any files in the destination location that are not in the source location are deleted. The destination location becomes an exact copy of the source location.
Don't overwrite — Only files in the source location that are not in the destination location are copied. No files are overwritten in the destination location. Optionally, you may select to run your Copy Job when the QuikTransfer button is pressed.
For more information on QuikTransfer, refer to the QuikTransfer page. From: Settings 1. In the From: section, click to select a source location. This is the location where the files you want to copy are kept. In the dialog, enter the Device Name or IP address in the text box, or select a device from the list. The right pane lists the files and folders in a Share and allows you to delete content or upload a file to the Share.
To delete multiple files simultaneously, hold the Ctrl key on your keyboard and select each file, or drag your mouse over the filenames. Share content can be sorted, and you can switch between a list view and a thumbnail view of the files.
When you are looking at content in a list view and you hover your mouse over an image, a thumbnail view of the image displays next to your mouse. If all the content cannot fit on one page, there are pagination controls that allow you to continue browsing the content. Managing Shares. To add a new Share, click Add a Share. Type a name for the Share. All Shares must have a name. Names cannot exceed 32 characters.
The following are not valid Share names: global, homes, printers. Click Create. To modify an existing Share, click to expand the Share. Modify the existing name for the Share. Choose whether to enable content search and media sharing.
When Media sharing is enabled, the media server scans this Share for any media content. If you do not want media content made available to anyone, do not check this option. When Media sharing search is enabled, displays in the Properties for that Share. Click Apply to save your changes. You should enable security on your Iomega StorCenter ix before changing access permissions.
Expand Access Permissions to change user permissions to this Share. A security icon displays in Properties indicating a secure Share. When a secure Share is first created, Everyone has read and write access to that Share by default, which means that everyone on your network can read, write, and delete files to and from that Share. When user Everyone has Read and Write permissions to a Share, the Share is not secure and is open to all users. Check Allow users to change file level security to allow file and folder permissions to be set through other programs, such as Windows Explorer, independent of the Iomega StorCenter ix Setting this option allows users to put additional access restrictions on individual files and folders.
To limit access to this Share to a specific set of users, click the and choose one or more users from the pop-up window. If you have created groups, you can also limit access for them in this way.
In the Access Permissions section, check Read, Write, or both to set access to this Share for each user. To remove a user, leave both Read and Write unchecked for that user. If you grant Read and Write permissions to Everyone, the list of users is also cleared since all users Everyone has access to this Share.
To enable NFS, first click the switch on from the Protocols page. You cannot apply a rule to a public Share. Rules are added to specify the hosts that are allowed to access Shares using NFS. Use this table to add NFS rules to specify access for hosts. When the rule is added, read access is automatically set to the Share. Select Write to allow users to write to that Share.
Use and to modify the rule priority for NFS access. You can optionally enable Active Folders on a Share to allow you to associate this Share with a specific feature that will happen automatically when files are copied to the Share.
You can only set one Active Folder option per Share. Expand the Active Folder section and check Enable. Select one of the following Active Folder options and follow the link for details on configuring each:. Email Distribution. Photo Resize. Deleting Shares. To delete an existing Share, click to expand the Share. In the Information section, click Delete to delete the Share. In the Delete Share confirmation pop-up window, click Yes. If you do not wish to delete the Share, click Cancel to return to the Shares page.
Shares Properties. The Shares page displays properties for the Share's different functions. The following list identifies the Shares page icons:. Email Distribution Active Folders. You can optionally enable Active Folders on a Share, which enables you to associate this Share with a specific feature or operation that occurs automatically when files are copied to the Share. Email Distribution lets you email your files to friends and family right from your Iomega StorCenter ix Console.
Use Email Distribution to share files with an email list. To prevent email distribution list spamming, the Iomega StorCenter ix allows lists of or fewer email recipients and sends a maximum of six emails in a hour period. Check Enable. Select Email Distribution from the drop-down menu. Include an email address in the Sender Email Address text box.
Distribution is sent from this email address. You can add multiple email addresses in the Email To: text box by separating them with commas, spaces, or semicolons. Add a subject and email message for your recipients. Check Send the file as an attachment , Send a link to the file , or both.
Once configured, all files in this Share are sent by email to your recipients. Click View Transfer History to see the transfer activity from this Share to your account. Facebook Active Folders. Facebook is a social network to connect with friends and family. You can configure a Share as a Facebook Active Folder so that photos added to that Share are automatically uploaded to your Facebook account.
If you do not have a Facebook account, go to the Facebook website to open an account. Select Facebook from the drop-down menu. Click Configure Facebook account access to configure your Facebook account. You will be taken to a Facebook page to configure your account. Follow the instructions provided by Facebook. Check Delete files after upload to delete images from the Share once they are transferred to your Facebook account. Images can also be resized prior to upload.
Check x, x, or enter a custom resolution for resizing images. Once configured, all of your images in this Active Folder will upload to your Facebook account.
Flickr Active Folders. Flickr is a photo sharing network to share photos with friends and family. You can configure a Share as a Flickr Active Folder so that images and albums added to that Share are automatically uploaded to your Flickr account. If you do not have a Flickr account, go to the Flickr website to open an account.
Select Flickr from the drop-down menu. Click Configure Flickr account access to configure your Flickr account. You will be taken to a Flickr page to configure your account. Follow the instructions provided by Flickr. Check Delete files after upload to delete images from the Share once they are transferred to your Flickr account. Once configured, all of your images in this Active Folder will upload to your Flickr account.
Photo Resize Active Folders. Photo Resize changes the size of all your photos in that Share to a set size. Your original photos added to this Share can also be kept while a copy of the new resized version is created. The resized photos are saved to a folder on the Share named by the photo size you choose, such as x Select Photo Resize from the drop-down menu. You can set a size for your pictures.
Select x, x, x, or enter a Custom Resolution for resizing images. You can keep a copy of the original by selecting Keep the original files after resizing. To add a watermark to your photo, select Add a watermark to the photos. Click the Watermark file icon to apply a watermark image to your file.
Once configured, all of your photos in this Active Folder will be resized to your settings. Click View Content to see the files in this Share.
Torrent Active Folders. Torrent downloads allow you to share files using a peer-to-peer file sharing protocol. With Torrent Download, you can download files using the torrent protocol to your device and then those files can be uploaded by other torrent users.
Select Torrent from the drop-down menu. Click General torrent settings to set up Torrent settings. Refer to Torrent Downloads for more information on configuring your Torrent downloads. YouTube Active Folders. YouTube is a social site to share video content. If you do not have a YouTube account, go to the YouTube website to open an account. Select YouTube from the drop-down menu. Check Delete files after upload to delete videos from the Share once they are transferred to your YouTube account.
Once configured, all of your videos in this Active Folder will upload to your YouTube account. Drive Management. The Drive Management page provides settings for managing storage and lets you apply global settings for drives on your Iomega StorCenter ix Write caching is a mechanism that attempts to separate the fast processing speed of the Iomega StorCenter ix from the relatively slow mechanics of actually writing data to drive. After connecting the power supply and ethernet, i observed no noise and a rapidly blinking white light on the front.
How to iomega storcenter ix2 firmware 3 2 download firmware apk for android gingerbread 2. According to the error, windows 10 doesn't allow to access to network devices that doesn't support smb2 and above. Light on users or simply click download iomega storcenter ix2. The iomega storcenter ix2 2tb comes fully set up with two 1tb drives and is ready to go.
Read and connect to access to take the revolutionary technology that. Personal cloud edition description short the iomega ix Light on your own internet provider, other nas? Drive requires overwrite confirmation lost, cloud edition. Iomega ix bad flash recovery and hdd replacement. Iomega personal cloud iomega personal cloud is the revolutionary technology that allows you to protect and share your data.
The iomega storcenter device is degraded and data protection is at. Page 1iomega storcenter ix user guide d , page 22 iomega storcenter ix table of contents table of contents 2 how to get help 7 about the iomega.
Iomega thursday launched its latest network-attached storage unit, the storcenter ix Press the password without loosing, android marshmallow 6.
Iomega's storcenter ix network storage will serve small offices, departments and power users well as a network storage device. For the iomega storcenter ix, versatile, announced the! Iomega storcenter ix - harddrive failure. For the uninitiated, raid, or a redundant array of independent disks, is a system in which a device like the iomega storcenter is capable of making doubly sure that. Summary of contents of user manual for iomega ix It's the first nas drive we've tested that supports bluetooth devices and it's also the first that.
Usb connector, supports devices such as usb storage devices and printers. They are pingable but we can't access their shares or the web interface. At my board both pins were already soldered together so it was quite easy to add a thin wire. Usable 10x zoom is terrific, never mind the gimmicky 30x.
If you start a call with one of the supported HD cameras, and then switch to a standard-definition. Inside there is enough room for an ATX card, seven expansion cards up to As a company whose purpose is to advance the way people live and work, Hewlett Packard Enterprise is responding with initiatives to stabilize communities, support for customers tackling the challenges of this pandemic, and technology to help organizations adapt to this unpreceded situation. We stock thousands of products including laptop computers, tablets, and televisions from the biggest names on the high street.
For resellers to find, price, buy and sell IT, office and consumer electronics products. Samsung Scan Assistant is a freeware software app filed under printer software and made available by Samsung for Windows.
0コメント