Place the battery pack in the battery charger and plug the charger into a power outlet. The charge indicator lights red while charging and changes to green when the battery pack is charged. Slide the battery cover open and press the battery lock while you insert the battery pack. Insert the battery pack correctly by aligning the arrows on the camera and battery pack.
Aim the camera and lightly press halfway the shutter button. Two beeps will sound when the autofocus is set. Press the shutter button all the way. One beep will sound when the shot is complete. The recorded image displays for approximately 2 seconds. To continue displaying the image, keep the shutter button pressed or hold the shutter button until you press the button and then release both.
Press the button while the image is displayed. Confirm that [Erase] is selected. Please refer to the System Map supplied with the camera for direct print function compatible printers. Lights when the power is on or transmission preparations are complete when connected to a computer. Wide Angle p. Replay: Magnify p. Index p. Photo Effects p. Blinking Orange: Ready to shoot but shutter speed is slow camera shake warning. Although you can press the shutter button, you are recommended to use the focus lock p.
It will change to green when the charge is complete. It can be recharged at any point. This is not a malfunction. The battery pack could fly out. Under these conditions, resuscitate the battery pack by warming it in a pocket immediately before use. However, ensure that there are no metallic items in the pocket that could cause a short circuit, such as a key holder, etc. Heat will build up and could result in a fire. This will shorten battery life. A , as this can damage the battery pack.
To carry the battery pack or store it during periods of disuse, always replace the terminal cover Fig. B or place it in the supplied case and store it in a cool, dry place.
Recharge it fully before using it again. Battery Pack NB-1L optional can also be used with the camera. The camera is writing, reading, erasing or transmitting an image to or from the CF card. The following icons and messages will display when the battery pack charge is low. Battery pack charge is low. Recharge it as soon as possible before it is required for an extended period.
Turn the camera power off and insert the CF card with the following procedures. Close the CF card slot cover. It could corrupt the image data. The card supplied with the camera may be used without further formatting. Do not bend them, apply force to them, or subject them to shocks or vibration. To avoid condensation, place the CF card in a sealed plastic bag before moving it into a different temperature zone and allow it to adjust slowly to the new temperature. If condensation forms on the CF card, store it at room temperature until the water droplets have evaporated naturally.
Start from Step 3 to set the date and time. Reset them when this occurs. This battery is recharged by the battery pack while it is in the camera. Use the above method to recharge it. The language in which menus and messages are displayed can be selected with this function. However, language settings cannot be adjusted while a printer is connected.
Reset the date and time when this occurs p. This camera is equipped with a power-saving function. The power will automatically shut down under the following circumstances when this function is set to On.
Powers down approximately 3 minutes after the last control is accessed on the camera. The LCD monitor automatically turns off 3 minutes after the last control is accessed even if this function is set to Off. Powers down approximately 5 minutes after the last control is accessed on the camera. Powers down approximately 5 minutes after the last control is accessed on the camera or something is printed on a connected printer.
A warning message displays on the computer screen approximately 5 minutes after the last control is accessed. Powers down approximately 1 minute later if no control is accessed. Slide the mode switch to. The LCD monitor can be used to compose images while shooting, adjust settings menus and replay images.
This does not constitute a malfunction. Shooting Mode or on the mode switch. When using this camera to shoot scenes containing extremely bright subjects, a vertical, red bar of light may appear on the LCD monitor. This is a normal occurrence in devices containing CCDs and does not constitute a malfunction. This red bar of light will not be recorded when shooting still photos, but it will be recorded when shooting movies.
Replay Mode on the mode switch. In shooting mode, information about the current settings and remaining image capacity will display on the LCD monitor for approximately six seconds when the actions below are taken, regardless of whether the LCD monitor is set to On or Off. While this information is displayed, you may set the flash, continuous mode, self-timer, macro and infinity settings. Hi, 1. Were there any changes made on the computer? Were you able to use camera on the computer before? Do you get any error messages?
Method 1: I would suggest you to try downloading Softwares or Firmwares for Cannon Powershot S and check if it helps. Method 2: Try to run the hardware troubleshooter and check what the issue is and fix it accordingly. Exposure Control Method. Exposure Compensation.
White Balance Control. Built-in Flash. Shooting Modes. Photo Effects. Continuous Shooting. Storage Media. File Format. Print Order Format. Image Recording Format. Number of Recording Pixels. Small: x , Medium 2: 1, x , Medium 1: 1,x1,, Large: 2, x 1,, Movie: x , x or x Image data. These figures reflect standard shooting conditions established by Canon. Actual totals and file sizes may vary according to the subject, shooting conditions and shooting mode.
Movie data. Individual clips are limited to 30 seconds x or 3 minutes x or x Above-written figures are measured under Canon's standard conditions and may vary depending on the scene, subjects or camera settings.
Playback Modes File. Single, Index 9 thumbnail images , Magnification 2x to 10x , or Slide Show. Erase Modes. Computer Interface. Operating System. Select OS Version. Software Firmware Utilities Loading There is no software for the OS Version you selected.
There is no firmware for the OS version you selected. There is no utility for the OS Version you selected. Search Our Knowledge Base Please enter your question: Examples: "prints missing colors", "flashing power light", "setting the white balance". There are no Recommended Downloads available. This limited warranty covers all defects encountered in normal use of the Products, and does not apply in the following cases: Loss of or damage to the Product due to abuse, mishandling, improper packaging by you, alteration, accident, electrical current fluctuations, failure to follow operating, maintenance or environmental instructions prescribed in Canon U.
Use of parts or supplies other than those sold by Canon U. If the Product has had its serial number or dating altered or removed. Main Unit Spec. Type of Camera Type. Total Pixels. Effective Pixels. Focal Length. Digital Zoom. Autofocus System. Optical Viewfinder. LCD Monitor. LCD Coverage. Maximum Aperture. Shutter Speed. Long speeds from 1 sec. Light Metering Method. Exposure Control Method. Exposure Compensation. White Balance Control. Built-in Flash. Shooting Modes.
Photo Effects. Continuous Shooting.
0コメント